|
|
STTC-X01
Conical sharp tip. 1.0 mm wide. |
|
|
|
STTC-X01P
Conical Sharp 1mm |
| These tips are only available in the 700 series temperature range. |
|
|
STTC-X02
Conical sharp tip. 1.78 mm wide. |
|
|
|
STTC-X03
Chisel tip 90 degrees 3.0 mm wide |
|
|
|
STTC-X04
Chisel tip 90 degrees 1.78 mm wide. |
|
|
|
STTC-X05
Bevel Soldering Tip 30 degrees 1.78 mm wide. |
|
|
|
STTC-X06
Conical Sharp Tip 0.4 mm wide. Long reach |
| For limited accesss SMT assembly and rework. |
|
|
STTC-X07
Conical sharp tip 1.0mm wide |
| General purpose SMT and through hole tip when access is limited. |
|
|
STTC-X11
Conical Soldering Tip. 0.5 mm wide. |
|
|
|
STTC-X12
Conical soldering Tip 2.03 mm wide. |
|
|
|
STTC-X13
Chisel tip 90 degrees 3.0 mm wide |
|
|
|
STTC-X14
Bevel soldering Tip 45 degrees. 2.03 mm wide. |
|
|
|
SMTC-X147
This speciality tip is designed drag soldering. The end of the tip is concave, simply melt a little solder into the recess and apply to the lead out. Then procede to smoothly slide from lead to lead to create a perfect joint.Ideal for replacing gull wing devices and removing solder shorts. |
|
|
|
STTC-X16
Conical Soldering Tip.0.5 mm wide. |
|
|
|
SMTC-X161
The knife tip geometry with a tinned area 2.03 mm can be used in a similiar way to that of the hoof tip range in that it is designed to remove solder shorts and reflow the solder joints on a number of lead outs. |
|
|
|
SMTC-X167
This speciality mini-hoof tip is designed drag soldering. The end of the tip is concave, simply melt a little solder into the recess and apply to the lead out. Then procede to smoothly slide from lead to lead to create a perfect joint.Ideal for replacing gull wing devices and removing solder shorts. |
|
|
|
SMTC-X169
This speciality long reach tip is designed drag soldering. The end of the tip is concave, simply melt a little solder into the recess and apply to the lead out. Then procede to smoothly slide from lead to lead to create a perfect joint.Ideal for replacing gull wing devices and removing solder shorts. |
|
|
|
STTC-X17
Extra large chisel tip 5.0 mm wide. |
|
|
|
SMTC-X170
This speciality long reach tip is designed drag soldering. The end of the tip is concave, simply melt a little solder into the recess and apply to the lead out. Then procede to smoothly slide from lead to lead to create a perfect joint.Ideal for replacing gull wing devices and removing solder shorts. |
|
|
|
SMTC-X171
Designed to remove 0201 and 0402 components from a topside angle. This design increases microscope viewing when reworking / removing micro chip capacitors /components. |
|
|
|
SMTC-X172
Designed for fine drag soldering and point to point soldering.This tip increases access between components and allows for leadlead to lead or solder bridge clean-up |
|
|
|
SMTC-X173
This knife tip with an increased tinned area is suitable for drag soldering and debridging between component devices. |
|
|
|
STTC-X173P
Knife 5.0 mm wide |
| This soldering cartridge is only available in 700 series temperature range. |
|
|
SMTC-X174
Long reach micro hoof tip designed with a smaller surface area than the mini hoof for optimal drag soldering of components intight spots. |
|
|
|
SMTC-X175
Micro-hoof tip designed with a smaller surface area than the mini hoof drag soldering of small / micro leaded components. |
|
|
|
STTC-X20
Long reach chisel 3.8 mm wide. |
|
|
|
STTC-X22
Conical sharp tip 0.4 mm Wide. |
| This sharp tip cartridge is ideal for soldering small SMT components or fine wire applications (would not be suitable for through hole soldering) |
|
|
STTC-X25
Chisel tip 30 degrees 1.0 mm wide |
| Good for a variety of light soldering tasks. Looking for a Surface Mount touch up tip? The STTC-125 should be your first choice . |
|
|
STTC-X25P
Chisel 30 degrees 1mm wide. |
| This tip is only available in 700 series temperature range. |
|
|
STTC-X26
Sharp soldering Tip Bent 30 degrees. 0.4 mm wide. |
|
|
|
STTC-X31
Conical Sharp soldering Tip. 1.0 mm wide. |
|
|
|
STTC-X32
Conical sharp tip 1.78 mm wide. |
|
|
|
STTC-X33
Chisel tip 2.5 mm wide |
|
|
|
STTC-X35
Bevel Soldering Tip. 30 degrees . 1.78 mm wide. |
|
|
|
STTC-X36
Chisel tip 30 degrees2.5 mm |
| For medium to heavy load joints requiring extra reach. |
|
|
STTC-X36P
Chisel 30 degrees 2.5 mm wide |
| This soldering cartridge is only available in 700 series temperature range. |
|
|
STTC-X37
Chisel Tip 30 degrees 1.78 mm |
| Excellent first choice for your new system. Will tackle a wide variety of tasks. |
|
|
STTC-X37P
Chisel 30 degrees 1.8 mm wide. |
| This soldering cartridge is only available in 700 series temperature range |
|
|
STTC-X38
Chisel Tip 30 degrees 1.5 mm |
| A finer version of the STTC-137 Ideal for medium to light through hole and general surface mount touch up. |
|
|
STTC-X40
Sharp Tip Bent 30 degrees 0.4 mm wide. |
| The bend in the tip makes it much easier to work on small circuits and PLCC |
|
|
STTC-X41
Chisel Tip 30 degrees 1.3 mm wide. |
|
|
|
STTC-X42
Long reach Chisel soldering tip 60 degrees 1.78 mm wide. |
|
|
|
STTC-X43
Conical Sharp Soldering Tip 0.5 mm wide. |
|
|
|
STTC-X44
Sharp Soldering Tip Bent 30 degrees 0.5 mm wide. |
|
|
|
STTC-X45
Bevel tip 60 degree 0.4 mm. |
| An extended length fine tip for surface mount or fine wire applications would not be ideal for general through hole tasks. |
|
|
STTC-X45P
Conical 0.4 mm |
| This soldering cartridge is only available in 700 series temperature range. |
|
|
STTC-X47
Bevel soldering Tip. 60 degrees 1.78 mm wide. |
|
|
|
STTC-X47P
Bevel 60 degrees 1.78 mm wide |
| This soldering cartridge is only available in 700 series temperature range. |
|
|
SMTC-X60
This speciality tip at 10.41 mm wide can be used for in line soldering over a number of lead outs or for cleaning up BGA and SMD pads when used in conjunction with solder braid. |
|
|
|
SMTC-X61
This speciality tip at 15.75 mm wide can be used for in line soldering over a number of lead outs or for cleaning up BGA and SMD pads when used in conjunction with solder braid. |
|
|
|
SMTC-X62
This speciality tip at 22.10 mm wide can be used for in line soldering over a number of lead outs or for cleaning up BGA and SMD pads when used in conjunction with solder braid. |
|
|
|
STTC-X65
Large chisel Long reach 5.0 mm wide |
|
|
|
STTC-X83
Conical tip , grooved 2.0 mm wide. |
|
|
|
STTC-X90
Microfine tip designed for soldering and touch-up of micro components such as 0201 and 0402. |
|
|
|
STTC-X98
Chisel tip, Bent, 30 degrees 1.78 mm wide |
|
|
|
STTC-X99
Chisel Tip, Bent , 1.5 mm wide |
|
|
